Blauberg Vento Ergo A50-1 Pro V.3
- Description
- Characteristics
- Downloads
- Designation key
- Dimensions
- Technical data
- Accessories
FEATURES | |
Arrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises.Heat recovery minimises ventilation heat losses.Humidity balance and controllable air exchange create individually set microclimate.Coordinated network based on several integrated single-room ventilation units with central control. |
|
DESIGN | |
HEAT AND HUMIDITY REGENERATION | |
High-tech ceramic energy accumulator with heat recovery up to 88 %. |
Due to its cellular structure it has a larger heat transfer area surface and high efficiency. The energy accumulator is featured with excellent heat-conducting properties and thermal energy storage capacity. |
UNIT OPERATING LOGIC IN WINTER PERIOD | |
Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers a part of the accumulated heat and moisture to it.In 70 seconds, after heating of the ceramic regenerator, the unit switches to the supply mode. |
Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.In 70 seconds, after cooling of the ceramic regenerator, the unit is switched to the extract air mode. |
CONTROL | |
The unit operation mode control is performed by means of manual three-position switches located on the unit casing or using the remote controller.The unit is equipped with a humidity sensor for indoor humidity control and regulation.Connection of the units into one ventilation system provide balanced ventilation and central control.Remote control and operation mode selection: |
|
Connection of several units in series enables their synchronous control by the first unit. The signal from the remote control is received by the first unit only. |
|
MOUNTING | |
The unit is designed for external through-the-wall installation inside a prepared round hole in the outer wall of the building.The best ventilation solution is pairwise installation of reverse phase connected units. Some units supply fresh air to the room and the other units extract stale air from the room. This allows to arrange the most efficient balanced ventilation. |
In case of brand new construction the units are mounted in two stages:
If mounting of the ventilation hood on the outer wall is undesirable it may be flush mounted and the external grille may be inserted into the outer window jamb using the KIT BlauPlast 204x60-1 pre-installation kit. Available upon separate order. |
Parameter | Vento Ergo A50-1 Pro V.3 (1 speed) |
Vento Ergo A50-1 Pro V.3 (2 speed) |
Vento Ergo A50-1 Pro V.3 (3 speed) |
Measurement unit |
---|---|---|---|---|
Speed | I | II | III | - |
Phase | 1 | 1 | 1 | ˜ |
Voltage | 100-240 | 100-240 | 100-240 | V |
Frequency | 50/60 | 50/60 | 50/60 | Hz |
Power | 4.5 | 5 | 7 | W |
Current | 0.024 | 0.026 | 0.039 | A |
RPM | 610 | 800 | 1450 | min-1 |
Maximum air flow | 6 | 10 | 14 | l/s |
Maximum air flow | 20 | 35 | 50 | m³/h |
Air flow in heat recovery mode | 10 | 18 | 25 | m³/h |
Air flow in heat recovery mode | 3 | 5 | 7 | l/s |
SFP | 1.62 | 1.03 | 1.01 | W/l/s |
Sound pressure level at 1 m in accordance with ISO 3741:2004 | 22 | 29 | 32 | dBА |
Sound pressure level at 3 m in accordance with ISO 3741:2004 | 13 | 20 | 23 | dBА |
Remote control panel | yes | yes | yes | - |
Transported air temperature | -20...+40 | -20...+40 | -20...+40 | °С |
Ingress protection rating | IP24 | IP24 | IP24 | - |
Filter | G3 (Option: G4, F8 PM2.5 > 99 %*) | G3 (Option: G4, F8 PM2.5 > 99 %*) | G3 (Option: G4, F8 PM2.5 > 99 %*) | - |
EC motor | yes | yes | yes | - |
Remote control panel | - | - | - | - |
Functions | Filter replacement indication, Timer, Humidity sensor | Filter replacement indication, Timer, Humidity sensor | Filter replacement indication, Timer, Humidity sensor | - |
Air duct | 150 | 150 | 150 | - |
Outdoor sound pressure attenuation in accordance with DIN EN 20140 | 40 | 40 | 40 | dBА |
Heat recovery efficiency in accordance with DIBt LÜ-A 20 | up to 88 | up to 88 | up to 88 | % |
* | Maximum air flow 40 m³/h | Maximum air flow 40 m³/h | Maximum air flow 40 m³/h | - |
Model | Air duct | Rated air flow [m³/h] |
Front panel | Hood type | Control | Version |
Vento Ergo | A: round air duct | 50 | -1: flat front panel |
_: white plastic hood AH-10 white 100 (for standard walls) |
Pro: three-position switches and remote control | V.3: plastic mounting plate, two boards, fuse on board |
|
Name | Description | |
Pre-installation Kit Vento Ergo A50 S10 Pro |
Pre-installation kit for mounting into a wall with standard thickness. Includes: |
|
Completion Kit Vento Ergo A50-1 Pro V.3 |
Includes: |
|
FP Vento Ergo A50 G3 |
G3 filters (2 pcs.) |
|
FPC 150x50 G4 |
G4 filter |
|
FP Vento Ergo A50 F8 |
F8 filter |
|
AH-8 white 150 | White painted aluminium outer ventilation hood with frost protection for a cold climate | |
AH-8 chrome 150 | Brushed stainless steel outer ventilation hood with frost protection for a cold climate | |
AH-10 *colour* 160 | Plastic outer ventilation hood. Available in colours: |
|
AH-10 chrome 160 | Plastic outer ventilation hood with a plate with brushed stainless steel effect finish | |
AH-S grey 150 | Outer ventilation hood for thin wall, painted grey | |
AH-S chrome 150 | Outer ventilation hood for thin wall made of brushed stainless steel | |
PP 160/0.5 | Outer ventilation hood for mounting from inside | |
KIT BlauPlast 204x60-1 |
Installation kit for angular mounting. Includes: |
|
FB Vento Ergo |
Remote control |