Blauberg KOMFORT Ultra L 250
- Capacity diagram
- Designation key
Air handling units for efficient supply and exhaust ventilation in flats, houses, cottages and other buildings. Heat and humidity recovery reduces ventilation heat losses in the cold season and the load on the air conditioners in the hot season. Heat recovery minimises ventilation heat losses. Control of air exchange for creating comfortable indoor microclimate. Compatible with round Ø 125 mm air ducts.DESIGN
The casing of KOMFORT Ultra L 250-H(E) S12 is made of double-skinned aluzinc panels, internally filled with 20 mm mineral wool layer for heat and sound insulation. The casing of KOMFORT Ultra L 250-H(E) S12 white is made of double-skinned white painted metal panels, internally filled with 20 mm mineral wool layer for heat and sound insulation. The spigots are located at the side of the unit and are rubber sealed for airtight connection to the air ducts. The hinged panel of the casing ensures easy access to the unit internals for service works including cleaning, filter replacement, etc.
Asynchronous external rotor motors and centrifugal impellers with backward curved blades are used for air supply and exhaust. Integrated motor overheating protection with automatic restart. Dynamically balanced impellers. Equipped with ball bearings for longer service life.Reliable and quiet operation.
The KOMFORT Ultra L 250-H S12 (white) unit is equipped with a plate cross-flow polystyrene heat exchanger for heat recovery. The unit condensate is collected and drained to the drain pan under the heat exchanger. The KOMFORT Ultra L 250-E S12 (white) unit is equipped with an enthalpy plate cross-flow heat exchanger for energy (heat and humidity) recovery. Due to humidity recovery condensate is not generated in the enthalpy heat exchanger. The air flows are completely separated in the heat exchanger. Thus smells and contaminants are not transferred from the extract air to the supply air. Heat recovery is based on heat and/or humidity transfer through the heat exchanger plates. In the cold season supply air is heated in the heat exchanger by transferring the heat energy of warm and humid extract air to the cold fresh air. Heat recovery minimizes ventilation heat losses and heating costs respectively. In the warm season the heat exchanger performs reverse and intake air is cooled in the heat exchanger by the cool extract air. That reduces operation load on air conditioners and saves electricity. When the indoor and outdoor temperature difference is insignificant, heat recovery is not reasonable. In this case the heat exchanger can be temporary replaced with a summer block for the warm season (available as a specially ordered accessory).FREEZE PROTECTION
The integrated automatic freeze protection is used to prevent freezing of the heat exchanger in the cold season. The supply fan turns off according to the temperature sensor to get the heat exchanger warmed up with extract air. After that the supply fan turns on and the unit continues to run in the standard mode.
The built-in G4 supply filter and G4 extract filter provide air filtration. The F8 supply filter (specially ordered accessory) may be used for efficient supply air filtration.CONTROL AND AUTOMATION
Smooth motor speed control from 0 up to 100 % by means of the thyristor speed controller SGS E1 (included in the delivery).MOUNTING
The units can be fixed to the wall or mounted on the floor using the mounting brackets. The KOMFORT Ultra L 250-E S12 (white) unit is also suitable for ceiling mounting. The KOMFORT Ultra L 250-H S12 (white) unit mounting position must provide condensate collection and drainage. While mounting provide free access to the service panel for filter replacement and servicing. Due to universal casing design both left and right mounting is possible. It requires swapping the service and the back panel.
- Selection method:
- Air capacity:
- Air capacity: --
- Pressure: ---
|Series||Unit type||Spigot modification||Rated air flow [m³/h]||Heat exchanger type||Control||Casing|
|KOMFORT||Ultra: compact unit||L: horizontal spigot orientation||250||–||Н: heat recovery
Е: energy recovery
|S12: speed controller SGS E1||_: aluzinc
white: white-painted steel
|KOMFORT Ultra L 250-H S12
KOMFORT Ultra L 250-H S12 white
|KOMFORT Ultra L 250-E S12
KOMFORT Ultra L 250-E S12 white
|G4 panel filter||FP 240x184x40 G4||FP 240x184x40 G4|
|F8 panel filter||FP 240x184x40 F8||FP 240x184x40 F8|
|Silencer||SD 125||SD 125|
|Backdraft air damper||VRV 125||VRV 125|
|Air damper||VK 125||VK 125|
|Summer block||SB C4 200/240||SB C4 200/240|