Login
Not registered yet? Take advantages of registration:
Products saving in a binding to the projects
Online consultation from experts
Signup

Privacy policy

Blauberg Vento Ergo A85(-1) S10 Pro1

  • Description
  • Modifications
  • Downloads
  • Designation key
  • Technical data
  • Accessories
Description
Description
FEATURES

Arrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises.Heat recovery minimises ventilation heat losses.Humidity balance and controllable air exchange create individually set microclimate.Coordinated network based on several integrated single-room ventilation units with central control.

DESIGN
HEAT AND MOISTURE REGENERATION  

High-tech ceramic energy accumulator with heat recovery up to 88 %.

Due to its cellular structure it has a larger heat transfer area surface and high efficiency. The energy accumulator is featured with excellent heat-conducting properties and thermal energy storage capacity.

UNIT OPERATING LOGIC IN WINTER PERIOD

Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers a part of the accumulated heat and moisture to it.In 70 seconds, after heating of the ceramic regenerator, the unit switches to the supply mode.

Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.In 70 seconds, after cooling of the ceramic regenerator, the unit is switched to the extract air mode.

CONTROL

The unit operation mode control is performed by means of manual three-position switches located on the unit casing or using the remote controller.The unit is equipped with a humidity sensor for indoor humidity control and regulation.Connection of the units into one ventilation system provide balanced ventilation and central control.Remote control and operation mode selection:

Connection of several units in series enables their synchronous control by the first unit. The signal from the remote control is received by the first unit only. Power 220 V must be supplied to the 1st and every 11th unit in a chain.

MOUNTING  

The unit is designed for external through-the-wall installation inside a prepared round hole in the outer wall of the building.The best ventilation solution is pairwise installation of reverse phase connected units. Some units supply fresh air to the room and the other units extract stale air from the room. This allows to arrange the most efficient balanced ventilation.

In case of brand new construction the units are mounted in two stages:

  • pre-installation at the stage of the indoor finishing and outer decorative wall finishing. It includes installation of the telescopic air ducts, outer ventilation hood and laying out of electric cables.
  • final mounting before commissioning of a house. It includes installation of the regenerator, the filters, connection of the ventilation unit.

If mounting of the ventilation hood on the outer wall is undesirable it may be flush mounted and the external grille may be inserted into the outer window jamb using the KIT BlauPlast 204x60-1 pre-installation kit. Available upon separate order.

Modifications
Modification name
Vento Ergo A85 S Pro1
Vento Ergo A85 S10 Pro1
Vento Ergo A85-1 S Pro1
Vento Ergo A85-1 S10 Pro1
+
+
+
+
Documents archieve
Documents archieve
Select a document type
  • Catalogues
  • Technical documentation
  • Certificates
Name
Vento Ergo A85(-1) S10 Pro1 - data sheet (pdf 1.42Mb)
Vento Ergo A85(-1) S10 Pro1 - image (png 394.45Kb)
Vento Ergo A85 S10 Pro1 - image (png 375.65Kb)
Vento Ergo A85-1 S10 Pro1 - image (png 387.68Kb)
Vento Ergo A85 S Pro1 - image (png 452.52Kb)
Vento Ergo A85-1 S Pro1 - image (png 452.52Kb)
Vento Ergo A85 S10 Pro1 - specification (pdf 49.79Kb)
Vento Ergo A85-1 S10 Pro1 - specification (pdf 34.92Kb)
Vento Ergo A85 S Pro1 - specification (pdf 41.23Kb)
Vento Ergo A85-1 S Pro1 - specification (pdf 41.22Kb)
Vento Ergo A85 S10 Pro1 - energy label (pdf 56.47Kb)
Vento Ergo A85-1 S10 Pro1 - energy label (pdf 56.54Kb)
Vento Ergo A85 S Pro1 - energy label (pdf 93.37Kb)
Vento Ergo A85-1 S Pro1 - energy label (pdf 93.45Kb)
Vento Ergo A85(-1) Pro1 - user's manual (pdf 5.32Mb)
Designation key
Designation key
Model Air duct Rated air flow [m³/h] Front panel Hood type Control
Vento Ergo A: round air duct 85 _: no flat front panel
-1: flat front panel

S10: white plastic hood AH-10 white 100
S: AH-S chrome 150 metal hood for thin walls

Pro1: three-position switches and remote control
Technical data
Technical data
Parameters Vento Ergo A85 S10 Pro1
Vento Ergo A85-1 S10 Pro1
Speed I II III
Voltage [V / 50 (60) Hz] 1 ~ 100-230
Power [W] 4.74 6.56 9.65
Current [A] 0.034 0.050 0.071
RPM [min⁻1] 1000 1500 2045
Maximum air flow [m³/h (l/s)] 36 (10) 59 (16) 85 (24)
Air flow in heat recovery mode [m³/h (l/s)] 18 (5) 30 (8) 43 (12)
SFP [W/l/s] 0.95 0.80 0.82
Filter G3 (Option: F8 PM2.5 > 99 %*)
Transported air temperature [°C] -20...+40
Sound pressure level at 1 m according to ISO 3741: 2004 [dBA] 29 35 44
Sound pressure level at 3 m according to ISO 3741: 2004 [dBA] 19 25 34
Outdoor sound pressure attenuation according to DIN EN 20140 [dBA] 40
Heat recovery efficiency according to DIBt LÜ-A 20 [%] up to 90
Ingress protection rating  IP24
* maximum air flow 40 m³/h  
Accessories
Accessories
Name   Description
Pre-installation Kit Vento Ergo A85 S10 Pro1

Pre-installation kit for mounting into a wall with standard thickness. Includes:
• Round telescopic air duct with the diameter of 150 mm and adjustable length from 240 to 460 mm
• AH-10 white 160 outer ventilation hood
• Plastic foam plug
• Plastic foam wedges

Completion Kit Vento Ergo A85 Pro1

Includes:
• Ceramic regenerator Ø 150 mm
• Vento Ergo A85 ventilation unit
• G3 filters
• Mounting plate
• Remote control

Completion Kit Vento Ergo A85-1 Pro1

Includes:
• Ceramic regenerator Ø 150 mm
• Vento Ergo A85-1 ventilation unit
• G3 filters
• Mounting plate
• Remote control

FP Vento Eco A50 G3

G3 filters (2 pcs.)

AH-10 *colour* 160   Plastic outer ventilation hood. Available in colours: 
AH-10 chrome 160   Plastic outer ventilation hood with a plate with brushed stainless steel effect finish
AH-S chrome 160 Outer ventilation hood for thin wall made of brushed stainless steel
AH-S grey 160 Outer ventilation hood for thin wall, painted grey
PP 160/0.5 Outer ventilation hood for mounting from inside
KIT BlauPlast 204x60-1  

Installation kit for angular mounting. Includes:
• Plastic ventilation grille 230x86 mm
• Plastic air duct 204x60 mm
• Plastic connecting bend from Ø 150 to 204x60 mm

FP Vento Ergo A50 F8  

F8 filter

FB Vento Ergo

Remote control