Login
Not registered yet? Take advantages of registration:
Products saving in a binding to the projects
Online consultation from experts
Signup

Privacy policy

Blauberg VENTO Ergo V50-1 S Pro


Heat recovery single-room units. Maximum air capacity up to 35 m³/h.
EAN codeEAN4058448022975
  • Description
  • Characteristics
  • Downloads
  • DIMENSIONS
  • Accessories
Description
Description
USE
Arrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises. Heat recovery minimises ventilation heat losses. Humidity balance and controllable air exchange create individually set microclimate. Coordinated network based on several integrated single-room ventilation units with central control.
DESIGN
HEAT AND MOISTURE REGENERATION  
High-tech ceramic energy accumulator with heat recovery up to 88 %. Due to its cellular structure it has a larger contact area surface and high efficiency. The energy accumulator is featured with excellent heatconducting properties and thermal energy storage capacity. 
UNIT OPERATING LOGIC IN WINTER PERIOD  
Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers a part of the accumulated heat and moisture to it. As the ceramic regenerator gets warmed up, the unit switches to the supply mode. Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.When the ceramic regenerator is cooled down, the unit is switched to the extract air mode.
CONTROL  
The unit operation mode control is performed by means of manual three-position switches located on the unit casing or using the remote controller.The unit is equipped with a humidity sensor for indoor humidity control and regulation.Connection of the units in series enables a central ventilation system. 
Remote control and operation mode selection: Connection of several units in series enables their synchronous control by the first unit. For connection of the units in series connect the contact socket on the mounting plate of the first unit to the contact socket of the second units. Connect the third unit with the second one in the same way, etc. The signal from the remote control is received by the first unit only.
MOUNTING  
The unit is designed for external through-the-wall installation inside a prepared square hole in the outer wall of the building.The best ventilation solution is pairwise installation of reverse phase connected units. Some units supply fresh air to the room and the other units extract stale air from the room. This allows to arrange the most efficient balanced ventilation. In case of brand new construction the units are mounted in two stages:
  • pre-installation at the stage of the indoor finishing and outer decorative wall finishing. It includes installation of the telescopic air ducts, outer ventilation hood and laying out of electric cables.
  • final mounting before commissioning of a house. It includes installation of the regenerator, the filters, connection of the ventilation unit.
Characteristics
Characteristics
Parameter VENTO Ergo V50-1 S Pro (1 speed) VENTO Ergo V50-1 S Pro (2 speed) VENTO Ergo V50-1 S Pro (3 speed) Measurement unit
Voltage 100-230 100-230 100-230 V
Frequency 50/60 50/60 50/60 Hz
Voltage 100-230 100-230 100-230 V
Power 4.31 4.92 5.8 W
Current 0.025 0.029 0.035 A
RPM 808 1264 1629 min-1
Air capacity 11 24 35 m³/h
Sound pressure level at 1 m 28 33 39 dBА
Sound pressure level at 3 m 19 24 29 dBА
Outdoor sound pressure attenuation 19 19 19 dBА
Regeneration efficiency ≤ 88 ≤ 88 ≤ 88 %
Ingress protection rating IP24 IP24 IP24 -
Remote control panel - - - -
Functions Filter replacement indication, Timer, Humidity sensor Filter replacement indication, Timer, Humidity sensor Filter replacement indication, Timer, Humidity sensor -
Air duct 150x150 150x150 150x150 -
SEC class A A A -
Mounting wall mounting wall mounting wall mounting -
Documents archieve
Documents archieve
Name
VENTO Ergo V50 Pro - data sheet (pdf 1.11Mb)
VENTO Ergo V50-1 S Pro - image (png 381.47Kb)
Vento Ergo V - certificate GS (pdf 215.26Kb)
Vento Ergo V - certificate LVD (pdf 146.81Kb)
Outer ventilation hood with frost protection AH-8 - installation instruction (pdf 1.42Mb)
DIMENSIONS
DIMENSIONS

Accessories
Accessories
ACCESSORY NAME DESCRIPTION
Pre-installation kit for mounting into a wall with standard thickness Pre-installation Kit VENTO Ergo V50 Includes:
  • Square telescopic air duct, section 150x150 mm, 250-470 mm long.
  • AH 150x150 outer ventilation hood.
  • Plastic foam plug.
  • Mounting plate.
Pre-installation kit for mounting into a thin wall Pre-installation Kit VENTO Ergo V50 S Includes:
  • Square telescopic air duct, section 150x150 mm, 120-430 mm long.
  • AH-S 150x150 outer ventilation hood.
  • Plastic foam plug.
  • Mounting plate.
Final mounting kit Completion Kit VENTO Ergo V50 Includes:
  • Ceramic regenerator 150x150 mm.
  • VENTO Ergo V50 ventilation unit.
  • G3 filters.
Final mounting kit Completion Kit VENTO Ergo V50-1 Includes:
  • Ceramic regenerator 150x150 mm.
  • VENTO Ergo V50-1 ventilation unit.
  • G3 filters.
Remote control FB-Vento Ergo For controlling the VENTO Ergo units.